TEH TAC10L 10L Oil-Free Air Compressor — 1300W — 190 L/min — 7 Bar — DIY & Home Workshop

Performance and Flow Rate Guide

The TAC10L delivers a consistent, linear flow curve from 190 L/min at 0 Bar down to 127 L/min at the maximum rated pressure of 7 Bar. The figures below represent actual free air delivery (FAD) at each pressure point, derived from the factory-measured performance chart. Always match your tool requirements against FAD — not displacement — when confirming suitability.

FAD (Free Air Delivery) is the actual usable airflow delivered at the outlet at the stated pressure. It is always lower than the theoretical max displacement figure. All tool matching must be based on FAD values.

Tool Compatibility and Simultaneous Use Guide

The TAC10L is rated for single-tool operation at full rated pressure. The table below shows confirmed compatible applications and the airflow requirements for each.

Continuous Full Support

• Tyre and ball inflation: Continuous operation — well within rated capacity at all pressures
• Blow guns and air dusters: Continuous use for cleaning and blowing — no restriction
• Brad nailers and pin nailers (1-2 CFM): Fully supported — consistent output with fast tank recovery
• Finish nailers and trim nailers (2-3 CFM): Continuous use for finish carpentry and trim applications
• Small airbrushing and touch-up spray guns (2-3 CFM): Suitable for detailed airbrushing, crafts, and light touch-up work at reduced pressure
• Staple guns and light fastening tools: Continuous operation — fully within rated capacity

Intermittent Support

• Light inflation tasks requiring short bursts: Tank recovery is fast — suitable for regular short-burst inflation work
• Small pneumatic caulking tools: Intermittent use — suitable with adequate recovery time between cycles

Perfect For

• Home DIY workshops and garages
• Tyre inflation for cars, bicycles, and sports equipment
• Brad and pin nailers for trim and finish carpentry
• Airbrushing, hobby painting, and craft projects
• Blow guns for cleaning and dusting
• On-the-go portable jobs requiring a lightweight compressor
• Light staple and fastening work
• Situations where ultra-quiet operation is essential

Key Features

• Ultra-Quiet 60 dB Operation: One of the quietest oil-free compressors in its class — suitable for home, office-adjacent, and noise-sensitive environments
• 100% Copper Winding Motor: Superior thermal stability, extended service life, and consistent output under sustained use
• 100% Oil-Free: Zero maintenance, no oil top-ups, no contamination risk, and no warm-up time required
• Portable Ergonomic Design: Lightweight with carry handle for easy transport between home, garage, and job site
• Automatic Pressure Control: Auto on/off maintains set tank pressure for stable, uninterrupted airflow
• Standard 13A Plug: No special wiring required — runs from any standard UK mains socket
• Instant Start: Ready to work immediately every time — no warm-up period
• 1 Year Warranty: Full manufacturer warranty covering parts and motor
• Free UK Mainland Delivery: Delivered direct to your door

TEH Oil-Free Air Compressor Range — Full Comparison

The TAC10L sits at the entry point of the TEH oil-free range. If your tool requirements exceed the TAC10L output, step up to the next model in the range using the guide below.

* Current model

Step Up: TEH TAC24L

24L | Single Motor | 2HP | 100 L/min (3.5 CFM) FAD at 8 Bar | Dual Pressure Gauges. For home DIY users who need a larger tank, 8 Bar working pressure, and dual gauge monitoring. Runs standard 13A plug.

Step Up: TEH TAC50L

50L | Twin Motor | 4HP | 200 L/min (7.0 CFM) FAD at 8 Bar | Up to 3 Simultaneous Tools. For professional trade and workshop use — framing nailers, full-size HVLP spray guns, and multi-tool operation.

Step Up: TEH TAC100L

100L | Triple Motor | 6HP | 300 L/min (10.6 CFM) FAD at 8 Bar | Up to 4 Simultaneous Tools. For demanding industrial and multi-bay workshop use. Requires 32A industrial supply.

Step Up: TEH TAC130L

130L | Quad Motor | 8HP | 400 L/min (14.1 CFM) FAD at 8 Bar | Up to 6 Simultaneous Tools. Flagship industrial model for bodyshops, manufacturing, and the most demanding environments. Requires 32A industrial supply.

UK Workshop Installation Guide

Power Requirement

The TAC10L runs from a standard 230V 13A UK mains socket. No special wiring, dedicated circuit, or industrial supply is required. Simply plug in and start working.

Daily Maintenance

Water condensate can collect in the tank during use. Open the drain valve at the base of the tank regularly to release any condensation. This takes less than 60 seconds and protects the tank from internal corrosion over time.

Positioning

Position the TAC10L on a stable, level surface with adequate ventilation around the motor. Do not operate in enclosed spaces without airflow. The carry handle allows easy repositioning as required.

Warranty and Support

WARRANTY: The TEH TAC10L is covered by a 1 Year Manufacturer Warranty from the date of purchase, covering manufacturing defects in parts and motor under normal operating conditions. Warranty is valid for UK purchases through TEH Tools UK. Regular tank drainage is required to maintain warranty validity.

Know Your Zone

TAC10L — Single motor | 1 tool | 127 L/min FAD at 7 Bar | Standard 13A plug | Ultra-quiet 60 dB | Ideal for home DIY, inflation, nail guns, and light portable use.

Need more power? The TEH TAC24L single motor delivers 100 L/min FAD at 8 Bar with dual pressure gauges and a larger 24L tank — ideal for extended home and light trade use.

For professional trade use: The TEH TAC50L twin motor delivers 200 L/min FAD at 8 Bar and supports up to 3 simultaneous tools.

For industrial use: The TEH TAC100L triple motor delivers 300 L/min FAD at 8 Bar and supports up to 4 simultaneous tools.

For maximum industrial power: The TEH TAC130L quad motor delivers 400 L/min FAD at 8 Bar and supports up to 6 simultaneous tools.